Promag CON-485 Series Provozní pokyny Strana 70
- Strana / 98
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
7 Procedure in operation Memo-Graph S
70 Endress+Hauser
Functions of the LEDs
“NamurNE44” setting (see “Set-up”):
- Green LED lights up: power supply OK
- Red LED lights up: measurement signal failure
- Red LED flashes: maintenance required, e.g. messages to be acknowledged,
calibration running
“NamurNE44+” setting (see “Set-up”):
same as “NE44”, additional signalling of LV violations by red LED
- Green LED lights up: production / batch running; no limit value violation
- Red LED lights up: measurement signal failure and/or limit value violation detection
- Red LED flashes: maintenance required, e.g. messages to be acknowledged,
calibration
!
Note!
with this, fundamental operating conditions can also be detected in case the screensaver is activated
(i.e. the display has been switched to dark).
“LEDs controlled by one/two digital inputs” setting (see “Set-up”):
• Digital inputs must be activated
– “green operating LED”:
the front-mounted green operating LED lights up when the digital input is active.
– “red fault LED”:
the front-mounted red fault LED lights up when the digital input is active.
– “H -> green, L -> red LED”
the front-mounted green operating LED lights up when the digital input is active (high).
The front-mounted red fault LED lights up when the digital input is inactive (low).
– “L -> green, H -> red LED”
the front-mounted green operating LED lights up when the digital input is inactive (low).
The front-mounted red fault LED lights up when the digital input is active (high).
7.1 Important functions in brief
“Login” key
Logging in at the device:
Login - Function - Login - select ID, enter password
Logging out at the device:
Login - Function - Logout - select ID, enter password
Changing password:
Login - Function - Change password - enter old password - enter new password,
confirm new password
“Product” key
Selecting product:
Product - Selection - Select product
Starting production / batch:
Product - Start - Enter password
Stopping production / batch:
Product - Stop - Enter password
- Safety Data Manager (SDM) 1
- Memo-Graph S 1
- Overview 2
- Brief overview 2
- CHANGE PROTOCOL 3
- Table of contents 5
- 1 Safety instructions 7
- 1.4 Operational safety 8
- 1.5 Return 8
- 2 Identification 9
- 2.1.2 Product structure 10
- 3 Installation 11
- 3.3 Installation instructions 12
- 3.4 Post-installation check 12
- 4 Wiring 13
- 4 Wiring Memo-Graph S 14
- 14 Endress+Hauser 14
- 4.2 Terminal diagram 15
- 4.2.5 CPU board (slot 0) 19
- Ethernet connection 21
- 4.4 Ingress protection class 22
- 4.5 Post-connection check 22
- Set-up to commissioning 23
- 5.5 Set-up using PC 26
- 5.7.1 Basic settings 27
- 5.7.2 Signal settings 31
- Factory setting “0” 32
- 36 Endress+Hauser 36
- # Warning! 37
- " Caution! 38
- Endress+Hauser 43 43
- 44 Endress+Hauser 44
- 5.7.4 Products 48
- 5.7.5 Texts 50
- 5.7.6 Administration 50
- 5.7.8 Service 53
- 5.9.1 RS 232 56
- 5.9.2 RS 485 56
- 5.9.3 PROFIBUS DP 56
- 5.10.2 MAC address 58
- 5.10.3 IP address allocation 58
- 5.10.4 Subnet mask allocation 59
- 5.10.5 Gateway allocation 59
- 21 CFR 11 61
- 6.2.3 Administration 63
- 6.2.5 Analogue inputs 64
- 6.3.1 General 64
- Endress+Hauser 67 67
- 68 Endress+Hauser 68
- 7 Procedure in operation 69
- 7.2 The functions in detail 72
- 7.2.3 Enter comment / text 74
- 7.2.5 Extras 74
- 7.2.6 Set-up 77
- 8Accessories 78
- Software 79
- Operating language 79
- RSG12A1 79
- 80 Endress+Hauser 80
- 9.4 Spare parts 81
- 9.4.2 Spare parts list 82
- Endress+Hauser 83 83
- 9.5 Repairs/return 84
- 9.6 Disposal 84
- Measured variable / 85
- _ _ _ _ _ 86
- 10.3 Output values 87
- 10.4 Power supply 87
- 10.5 Accuracy 88
- 10.6 Operating conditions 88
- 10.7 Mechanical construction 89
- 320 mm (12.6“) 91
- 320 mm (12.6 “) 91
- 254 mm (10 “) 91
- 10.9 Data storage 92
- 10.11 Accessories 93
- 10.12 Further documentation 93
- BA 138R/09/en/08.04 98
- 51006049 98
- FM+SGML 6.0 98
Související produkty a manuály pro Nástroje pro měření a rozvržení Promag CON-485 Series
(40 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.118 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce